Sometimes your computer wakes up when it should stay asleep, and doesn't go into standby when it should. The outdated drivers and automatic updates can cause serious damage to your computer. Here are 7 solutions, click MiniTool to get more information.

Windows 10 Won’t Stay Asleep

Sleep mode is the basic part of the Windows system. Most of you don’t turn the PC off every time, but put it to sleep mode to reduce power consumption and cool it down while maintaining the speedy access to the system.

However, the sleep mode in Windows 10 seems to be problematic. In other words, even if you can make your PC sleep, the PC will wake up without any interaction. Basically, it’s doesn’t stay in sleep mode as expected before using it.

We will provide some basic troubleshooting steps for you. If your computer won’t stay asleep, you can try the solutions listed below.

Sleeping Computers Are Vulnerable to New Cold Boot Attack
Sleeping Computers Are Vulnerable to New Cold Boot Attack

The F-Secure company says sleeping computers are vulnerable to the new variation of the cold boot attack even if the PC is fully encrypted.

Read More

7 Solutions to Fix Computer Won’t Stay Asleep

Now, we will introduce 7 solutuions to fix computer won’t stay asleep one by one.

Solution 1: Run the Troubleshooter

First, you should make sure that you have enabled sleep mode correctly. Then you should confirm that the sleep mode is indeed properly configured. You can follow the steps we provided below to confirm that.

Step 1: Choose Hardware and Sound after you launching Control Panel, and click Power Options.

Step 2: Click Change plan settings in the Preferred plans section.

click Change plan settings on your active Power plan

Step 3: Under the Put the computer to sleep section, you should set the time for PC to make it go to sleep.

Secondly, you can use the Windows built-in tool – Troubleshooter related to power to fix that computer wakes from sleep. All errors in the power configuration can be fixed by troubleshooter and it allows you to put your PC to sleep without having to wake up by yourself. You can run Troubleshooter by the following steps:

Step 1: Open Setting by pressing the Windows key and the I key at the same time.

Step 2: In the setting page, please choose Update & Security.

choose Update & Security

Step 3: Open Troubleshoot from the left panel.

Step 4: At lastlick Run the troubleshooter after clicking Power.

click Run the troubleshooter after expanding the Power Troubleshooter

Solution 2: Check the Drivers

According to users, Realtek sound drivers can cause the system wake-up for no reason. Thus, you should check if all drivers are installed properly. Here are the steps.

Step 1: You should navigate to Device Manager and update all major drivers.

Step 2: You should pay more attention to Sound, Display, and Network devices.

Alternatively, you can go to the official manufacturer’s website and download the appropriate drivers, even if the driver seems to be up-to-date. This is especially true for older devices that are known to have Windows 10 issues. So, if your computer won’t stay in the Sleep mode on Windows 10, you can try it.

Solution 3: Check the Advanced Power Options

You can reset all advanced power options to their default values. This will solve some problems, for example, computer configures the wrong advanced options for your active power plan. After this step, don’t forget to set the sleep mode preferences.

Here are the steps of resetting advanced power options to their default values.

Step 1: Choose Hardware and Sound after you launching Control Panel, and click Power Options.

Step 2: Click Change plan settings on your active power plan.

Step 3: Then click Change advanced power settings.

Step 4: Now, you just need to click Restore plan defaults and click OK to make the changes.

Restore plan defaults

Solution 4: Disable Specific Devices from Waking Up Your PC

There is a solution for you to find out which device is waking up your device. Then you can adjust its settings or even unplug it. Some third-party applications can help, but we will use Command Prompt. You can access peripherals and determine all power usage on your system by these commands.

The following are the steps:

Step 1: Input CMD in the search box, right-click to select Run as administrator.

Step 2: Type the following command: Powercfg -devicequery wake_armed and press Enter.

type the command Powercfg -devicequery wake_armed

Step 3: Then all the devices which can wake the PC from sleep will be listed. If you see the device you don’t use, type the command: Powercfg -devicedisablewake “devicename” and press Enter. Don’t forget to change the device name.

Step 4: At last, you need to close Command Prompt and restart your PC.

Solution 5: Use Sleep-Hibernation Hybrid Instead of Sleep

To fix the issue of computer won’t stay asleep, you can use Sleep-Hibernation. You can follow the steps:

Step 1: First launch Control Panel and choose Hardware and Sound, then click Power Options.

Step 2: Click Change plan settings on your active power plan.

Step 3: Click Change advanced power settings. Then expand Sleep and click Allow hybrid sleep.

Step 4: Turn Hybrid sleep on for both Battery and AC and click OK to confirm the changes.

turn Hybrid sleep on for both Battery and AC

Solution 6: Disable Fast Startup and Prevent Programs Starting with the System

In addition, we recommend you to disable the Fast Startup feature. As we all know, this newly introduced (relatively newer) feature can cause that the system can’t wake up occasionally without any reason. Here are steps to disable the Fast Startup feature.

Step 1: Open Control Panel, click Hardware and Sound and choose Power Options.

Step 2: In the left pane, click Choose what the power button does.

click Choose what the power button does

Step 3: Click Change settings that are currently unavailable and uncheck the Turn on fast startup (recommended) box and click Save changes.

uncheck the Turn on fast startup (recommended) box

Step 4: Shut down your PC and power it on again to confirm whether your computer won’t stay asleep.

In addition, we suggest that all startup third-party programs and their dedicated services should be disabled. This is known as Clean Boot. You can follow the instructions to disable the Clean Boot.

Step 1: Type msconfig in the Windows Search bar and open System Configuration.

Step 2: Check the Hide all Microsoft services box under the Services tab, and click Disable all to disable all active third-party services.

click Disable all to disable all active third-party services

Step 3: Next, select the Startup tab and go to Task Manager. Prevent all programs from starting with the system and confirm the changes.

Step 4: At last, restart your PC.

If you are unable to disable your antivirus software, we recommend that you uninstall it temporarily. You can install it again after determining which application is causing the computer wakeup.

Solution 7: Reset Your PC to Factory Values

Finally, if none of the above solutions can fix that Windows 10 won’t stay asleep, there is only one solution left. Whether it is good or bad, reset the PC to the factory value. This is more like a refresh of the system than reinstalling. Moreover, since most reports problems after the update, you should use this recovery option to resolve this issue.

Step 1: Type reset in the Search bar and open Reset this PC.

Step 2: Click Get started under the Reset this PC option.

click Get started to reset this PC

Step 3: Choose Keep my files and continue with the resetting process.

Tip: If you choose to remove everything, you had better back up your important files in advance, read this post – How to Backup Files on Windows 10? Try These Top 4 Ways.

Use MiniTool ShadowMaker to Back Up Your System

After offering you the solutions to fix Windows 10 won’t stay asleep, we have a suggestion for you. In case of something on your system, we suggest you backing up your system in advance. Now, we will introduce a free backup software for you – MiniTool ShadowMaker.

MiniTool ShadowMaker provides a one-click system backup solution. It supports backing up your system drive completely, including system partition, system reserved partition and EFI system partition. And you can image all of your data including computer settings, applications, drivers, system files and boot files.

The system backup is bootable. When the system crashes, you can restore your computer to a normal state, read this post – How to Restore Computer to Earlier Date in Windows 10/8/7 (2 Ways).

MiniTool ShadowMaker provides a Trial Edition that gives you 30-day free trial for all backup features. You can purchase its Pro Edition to use it permanently.

Now you can download MiniTool ShadowMaker Trial Edition to back up your system.

MiniTool ShadowMaker TrialClick to Download100%Clean & Safe

Now, let’s see how to back up your Windows system.

Step 1: Decide a Backup Mode

  1. Launch MiniTool ShadowMaker and keep using the trial edition.
  2. Please choose the computer to manage and click Connect in the Local section to enter the main interface.

choose this computer to manage and enter the main interface

Step 2: Choose Backup Source

  1. Go to the Backup page.
  2. This software selects the system partition and system reserved partition by default.

Step 3: Choose a Destination Path to Store Your System.>

  1. You can back up your system to an external hard drive, USB flash drive, NAS and more.
  2. Then choose a destination path to store your system and click OK. Here we take the New Volume (E) as an example.

select the drive you want to store the disk image

1. Please do not save a volume image file to the volume being backed up.
2. The destination that used to store system must have enough storage space.

Step 4: Start to Back Up

  1. Go back to the following interface.
  2. You have two options: click Back up Now to start the backup process immediately or click Back up Later to delay the backup process.

back up system now or later

1. To set advanced parameters for the current backup task, go to Options.
2. To specify a backup task to run on a regular basis, go to Schedule.
3. To manage disk space occupied by backup files, go to Backup Scheme.

Here are all the steps of how to back up system by MiniTool ShadowMaker.

Tip: In addition to the method mentioned above, here is another method to back up system disk. That is using the feature of MiniTool ShadowMaker – Clone Disk, read this post – The Best Alternative to Acronis Clone Software: MiniTool ShadowMaker.

Here are 7 solutions for you to fix that computer wakes from sleep. In addition, MiniTool ShadowMaker can help you back up system to protect your data. Share it on Twitter to let more people know.Click to tweet

Bottom Line

That’s all about how to fix computer won’t stay asleep. You can try these solutions one by one until you fix this issue successfully and you can try MiniTool ShadowMaker to back up your system in advance to protect your data. If you have any questions and suggestions, please contact us via [email protected] or leave a comment.

Computer Won’t Stay Asleep FAQ

? Is sleep mode bad for PC?
Hibernate and Sleep switch off the hard drive and display when they are not being used to reduce the computer’s power consumption. Neither mode is damaging to a computer’s hardware but a handful of programs don’t take too kindly to it and can freeze when the computer starts up.
? How do I get my PC out of sleep mode?
  1. Press the sleep keyboard shortcut.
  2. Press a standard key on the keyboard.
  3. Move the mouse.
  4. Quickly press the power button on the computer.
? Is sleep mode better than shut down?
The PC enters a low-power state in sleep mode. It takes longer to resume from hibernate than sleep, but hibernate uses much less power than sleep. You may be interested in this post – Should You Shut down, Sleep or Hibernate Windows 10 PC?
⛺ Why is my computer stuck in sleep mode?
If your computer isn’t turning on properly, it may be stuck in Sleep Mode. If your batteries are running low, your computer can also be stuck in sleep mode.
  • linkedin
  • reddit